Menu

EKINOPS en français

PRODUCTS

EKINOPS 360 PLATFORM

PM OPS2

Optical Protection Switch

PM OPS2

Pluggable dual window, single channel optical protection switch module. Supports both 1310nm and 1550nm opitcal windows.

The EKINOPS PM OPS2 is an optical switch module for the EKINOPS 360 family that provides 1+1(50 ms) or "Optical UPSR/SNCP" protection capability either at the WDM line level or card level for either 1310 nm or 1550 nm wavelengths. The PM OPS2 card is used in pairs, one at each endof the optical signal to be protected, and provides "bridge-and-select" protection functionality.

At the head end of the signal to be protected, each OPS provides a "Bridge" capability. It accepts an input signal and replicates that signal across two fiber outputs, providing an exact copy. On the other end of the signal to be protected, each corresponding OPS2 provides a "Select" capability. It receives the two outputs generated by the "Bridge" end OPS2 and "Selects" the one that is not currently in a loss of signal state. If neither is in a loss of signal state, the signal selected is dependent on the mode for which the OPS2 is programmed.

The PM OPS2 can be placed between a source optical signal and the EKINOPS 360 transponders in order to provide card level protection as follows:

PM OPS2 card level protection
Figure 1: Using PM OPS2 for card level protection on dual input signals

In Figure 1, the input signal (services) is being replicated to two transponders each. Each transponder carries a duplicate of the input signal across the network so that if any one card/transponder fails, the service will still reach its destination. The EKINOPS PM OPS2 can also be used to replicate and protect the composite WDM signal being transported by the EKINOPS 360 system. In order to do this, one can place the PM OPS2 on the line output of an EKINOPS 360 system where it can receive the composite WDM signal for replication.

PM OPS2 line protection
Figure 2: Using PM OPS2 for line protection on a composite signal

The EKINOPS PM OPS2 can be programmed to switch in 3 different modes:

  1. In Revertive mode, the PM OPS2 will switch from a primary signal to a backup signal whenthe primary signal fails. Upon restoration of the primary signal, the PM OPS2 will switch back.
  2. In Non-Revertive mode, neither signal is primary. The PM OPS2 will switch to the alternate signal when the signal it is using fails but will not revert to the original signal upon restoration. A failure of the new signal it is utilizing will however cause it to switch back to the original signal.
  3. In Manual mode, no automatic switch will take place. The network operator must manually switch the PM OPS2 from one signal to the other.

Management

The EKINOPS PM OPS2 module can be managed through SNMP or via the EKINOPS standard element level management interfaces, which include a Command Line Interface (CLI) and an EKINOPS java-based Graphical User Interface (GUI). The CLI is accessible via Secure Socket Shell (SSH) and Telnet remotely or via a local serial port locally on the management board.

Digital Diagnostics Management (DDM) is supported for optical interfaces. This includes link status, transmit (TX) and receive (RX) signal power monitoring, and operational temperature, as well as manufacturer and transceiver model information essential for inventory management.

The EKINOPS PM OPS2 module is also supported by Celestis NMS, the EKINOPS advanced Network Management System.

  • Card level and line level protection with 50 ms switch times
  • Supports either 1310 nm or 1550 nmclient wavelengths
  • Support for revertive, non-revertive, or manual switching modes
  • Digital Diagnostic Monitoring and management via SNMP or the EKINOPS Java Craft Interface (EEM)
  • Remote management through telnet or SSH

The EKINOPS PM OPS2 can be used for any application that requires line level or card level protection. The PM OPS2 is rate agnostic so, when used for card level protection, it can accept any optical signal as an input for protection meaning that it can be used to protect any service type. This type of redundancy is particularly important for applications like disaster recovery, datacenter interconnect and for carrier services where a high level of availability has been committed.

  • Datacenter interconnect
  • Disaster recovery
  • Business Ethernet services
  • Metro and access rings

Subscribe

Latest News

  • Colorado’s FORETHOUGHT.net Selects EKINOPS FlexRate™ Solution

    EKINOPS (Euronext Paris - FR0011466069 – EKI), a leading supplier of optical transport equipment and router solutions for service providers and telecom operators, today announces that FORETHOUGHT.net, one of Colorado’s largest, independently-owned internet, cloud and communications service providers, has deployed the EKINOPS 200G FlexRate™ solution to provide high bit rate connectivity between two of its major points-of-presence (PoP) in Grand Junction and Montrose. FORETHOUGHT provides wide-ranging advanced communication services throughout Colorado, particularly within rural and underserved areas.

     
  • EKINOPS announces Q1 2019 revenue: +11% growth

    EKINOPS (Euronext Paris - FR0011466069 – EKI), a leading supplier of telecommunications solutions for telecom operators, has published its revenue for the first quarter of 2019.

     
  • Discussions with Nokia Corporation discontinued

    Following press reports, EKINOPS (Euronext Paris - FR0011466069 – EKI) had announced on 18 October, 2018, that preliminary discussions with Nokia Corporation had been initiated regarding a possible acquisition of Alcatel Submarine Networks (ASN).

     

EKINOPS Worldwide

EKINOPS EMEA & APAC
Telephone +33 (0)1 77 71 12 00

EKINOPS AMERICAS
Telephone +1 (571) 385-4103

 

E-MAIL ALERTS

Receive automatically EKINOPS information in your inbox!